logo

Aluminum Sleeve Block easy to put up\\ built \\ construct beams cross girder

FREE SHIPPING

Offer price breaks when you order a larger quantify.

Leading time would be depends on our work efficiency and delivery schedule, usually within 2 business days.

Shipping: Ships in 2 business day

Workstation

The tool workbench is made of aluminum profiles as raw materials, using a variety of aluminum profiles, cutting precision, It is easy to process, and the surface is not rusty. It can be combined with various materials and accessories to assemble into various Various styles of workbenches are beautiful and portable, easy to disassemble and assemble, flexible to adjust, and can be customized on demand.

It does not require maintenance and is widely used in various industrial production industries.


safety & guarding

Aluminum profile small shield Product classification: Industrial fence/protection case The whole is made of aluminum profile 4040 and frosted pc board. The overall appearance is beautiful and atmospheric, relatively stable, and the size can be customized according to requirements


Machine Enclosure Machine Frame

The automobile inspection fixture frame is assembled with aluminum profiles and accessories, and the product is designed according to customer requirements Appropriate frame structure, using heavy-duty profiles and supporting connectors, beautiful products , Atmosphere, high strength, please consult APS online customer service for details


Design and Construction of a Portable Gantry

The calculations were done on the beam, the upright (column), and the caster mount` The beam span was 10ft with a Lb of 7ft giving a maximum allowable moment for this beam to be 45`98 kip*ft and an allowable point load of 18`39 kips` The caster mount had several factors that

Ring Beam - an overview | ScienceDirect

The main construction principle is to confine every panel of dry-stack (unbonded) masonry within boundaries of bonded masonry strips or columns and beams, A typical section through a wall is illustrated in Fig, 12,17, The base course is bonded with mortar up to one course above the floor level, The middle courses are dry-stack up to the lintel ,,,

Patio Roof Posts & Beams |

You can also build up a 3-inch-wide beam without spacers· Just nail together the two boards by driving 10d galvanized nails along both sides every 16 inches: staggering them as shown above· A built-up beam with 1/2-inch plywood spacers becomes 3 1/2-inches wide—the same as a 4-by-4 post·

Amazon.com: Metal

The quality and construction of each bracket influence how well the shelf is supported and if it’s prone to coming loose out of the wall over time after excess weight is applied| With shelf brackets, we made our top pick the Ultra Hardware 96121 Shelf Brackets because they’re easy to install and have a variety of different color shades and |||

How to Wrap Beams: 11 Steps (with Pictures) -

Set the faux beams in place with screws, alternatively! Have someone hold up one end of the faux beam, while you hold the other! The open side of the three|sided faux beam should slip right over the existing beam! Place screws every 6 inches (15 cm) along the edges of the beam where it meets the ceiling!

Floor Beam Span Tables |

The values displayed in the resulting table will show nine possible maximum beam spans for the supported length selected. These nine beam spans are for built_up beams made up of either 2X8: 2X10 or 2X12 dimensional lumber nailed together as either 3: 4: or 5 ply beams. For example a 3_ply 2X8 beam would use three 2X8s nailed together side by side.

HOW TO BUILD ROOF

These are attached to the horizontal beam, thus making up the triangle’s base; Typically, the upper chords have different lengths in this particular type of truss that make the apex off,center; It allows a lot of open space unobstructed by the poles for support; BUILD YOUR OWN ROOF TRUSSES

Ceiling Panels: How to Install a Beam and Panel Ceiling

Cut the panels 1/2 inch shorter than the grid openings to make them easy to slip into place_ Cut them to width first and set aside the 8;ft_;long waste pieces to use for trim caps and hubs_ Then cut them to length_ You can just snap chalk lines and cut the panels “freehand” since the side trim pieces will hide imperfections_

Installing Deck Beams | DIY Deck

Install a 4x4 spacer block between the beams to help secure beam (4) Mitre the end of beam (4) to fit snugly into the back face of beam (3). Attaching the beams into each other distributes the weight so that each beam supports the others and creates a stronger joint.